Talisman Metals PLC - Tirzzit Project Significant Channel Sample Results
RNS Number: 1306G
Talisman Metals PLC

Talisman Metals PLC
("Talisman" or the "Company")
Tirzzit Project Significant Channel Sample Results
Talisman Metals PLC ("Talisman" or the "Company") announces the results from recent channel sampling activities completed at the Tirzzit copper-silver project in
Highlight sample results include:
Channel TZ-CH001: 2.65m@1.71% Cu and 22.25ppm Ag - ended in mineralisation
Channel TZ-CH003: 0.94m@1.11% Cu and 6.00ppm Ag
Channel TZ-CH005: 1.63m@1.06% Cu and 4.25ppm Ag
Assay Results
Malachite mineralisation at surface within the Basal Series was channel sampled along strike over approximately 700m of the interpreted 4.6km trend, with approximately one channel sample collected every 100m. Results are summarised in Table 1. Along the 700m strike length the average intercept is 1.25m thick with grade of 1.21% Cu and 12.25ppm Ag (weighted average) and the alteration halo is about 2.00m thick on average (Map 1). Intercepts usually sit on the top of the Basal Series and the hanging wall coincides with the contact on dolomite material (Figure 1).
Results confirm that the mineralised horizon in the Basal Series identified during historical mapping shows lateral continuity, with values above cut-off grade (Cu Cut-Off Grade ≥0.3%) in all seven of seven channels over a strike length of 700m with copper (Cu) grades ranging from 0.75% to 1.74% and silver (Ag) grades ranging from 3 to 22ppm. Note that all the intervals are reported as true width.
Table 1: Intercepts and Anomalous Interval Summary Table

Note: Coordinates were collected with a hand GPS using the datum
Map 1: Tirzzit map of channel sample results with selected historical results

Methodology and QAQC
The sampling was done using channel sampling, with sub-vertical groves against outcrops dipping 30 Degrees to the North-North-West, cut with a circular saw on 63.5mm wide grove (HQ Core Diameter). True thickness of the sampling intervals were measured with a Jacob Staff.
A total of 6 QA/QC samples were inserted into the original samples, comprising approximately 5% blanks, 5% field duplicates, and 5% certified reference materials.
Samples were submitted to the ONHYM laboratory for sample preparation (crushing at 3mm, 85% pass and pulverised at 75microns) and multi-element analysis using a three-acid digestion (HCl-HNO₃-HF) with ICP-AES finish. The analytical method has a lower detection limit of 5 ppm for copper (Cu) and 1 ppm for silver (Ag).
Blank samples showed no evidence of contamination above three times the detection limit for Cu or Ag. Field duplicates demonstrated an acceptable repeatability, with an R² value of 0.93. Certified reference materials consistently returned copper values approximately 14% below certified values, and the Company is reviewing the potential analytical bias; however, the Company does not currently consider this issue to materially impact the interpretation of the results.
For the reporting of each intercept stated comprised of more than one sample and samples are of differing lengths. In this case the average grade for the full interval length was calculated by length-weighted averaging, a standard method for determining average grades.
About The Tirzzit Project
The Tirzzit Project (See Figure 2) is a sediment-hosted stratiform Cu-Ag system, located 225km east of the city of
Figure 1: Picture of channel samples TZ-CH001 with 2.65m @1.71% Cu and 22.25 ppm Ag ending in mineralisation @ 5m

Figure 2: Location Map of Tirzzit Project

Qualified Person
The technical disclosure in this news release has been approved by
End
For further information:
Talisman Metals PLC
Tel +353 (0) 1 525 6710
contactus@talismanmetalsplc.com
Beaumont Cornish Limited (Nominated Adviser)
Tel: +44 (0) 207 628 3396
CMC Markets UK Plc (Broker)
Thomas Smith /
Tel: +44 (0) 20 3003 8255
BlytheRay (Financial PR)
Tel: +44 (0) 20 7138 3204
JORC Code (2012) - Historical Exploration Results Disclaimer
The information in this announcement that relates to historical reported exploration results is based on, and fairly represents, information and supporting documentation prepared by previous operators and/or extracted from historical reports.
The historical exploration results referred to in this announcement were reported prior to the introduction of the JORC Code (2012) and have not been reported in accordance with the JORC Code (2012).
A Competent Person has not done sufficient work to disclose the historical exploration results in accordance with the JORC Code (2012). It is possible that following further evaluation and/or exploration work, the accuracy and reliability of the historical exploration results may not be confirmed.
The Company has not independently verified the historical exploration results, and no assurance can be given that future exploration work will result in the confirmation or upgrade of the historical results to JORC Code (2012) compliant Mineral Resources or Ore Reserves.
The Company considers the historical exploration results to be relevant as they provide an indication of the potential of the project. However, the information should not be relied upon as a representation of the current mineral resource or exploration potential.
Technical Glossary
|
Adit |
A nearly horizontal passage driven from the surface into a hillside or orebody, used to access mineralisation, facilitate drainage, provide ventilation, and enable the transport of personnel, equipment, or ore. |
|
Ag |
Silver |
|
Alteration halo |
A border of minerals produced by hydrothermal alteration in the rock surrounding other rock |
|
Basel Series |
A stratigraphic layer within a sediment basin that has properties conducive to hosting mineralisation. |
|
Cu |
Copper |
|
Channel sampling |
A systematic sampling method in which a continuous, linear sample is collected across an exposed rock face or outcrop, typically perpendicular to the mineralised structure, to obtain a representative measure of grade over a defined width. The sample is usually cut or chipped along a uniform channel to reflect the true thickness and composition of the mineralised interval. |
|
Hanging wall |
In a sediment-hosted copper deposit, the hanging wall is the rock sequence located above the mineralized horizon, orebody, fault, or stratiform copper layer. |
|
HCl-HNO₃-HF |
HCl - hydrochloric acid HNO₃ - nitric acid HF - hydrofluoric acid Dissolving silicate and sulfide minerals in a near-total or total digestion of rock samples and usually used to prepare samples for ICP-OES / ICP-MS analysis. |
|
ICP-AES |
Inductively Coupled Plasma Atomic Emission Spectrometer is a type of elemental analysis used in laboratories. |
|
Jacob staff |
A graduated measuring rod, commonly used with a compass or clinometer, to determine the true thickness of geological units and to measure stratigraphic sections, particularly on inclined or uneven outcrop surfaces. |
|
Malachite |
A secondary copper carbonate hydroxide mineral (Cu₂CO₃(OH)₂), typically bright green in colour, formed by the weathering and oxidation of primary copper sulphides. It commonly occurs as coatings, vein fillings, or disseminations in the oxidised zones of copper deposits and is widely used as an indicator of near-surface copper mineralisation. |
|
Ppm |
Parts per million |
|
R² value |
A statistical measure regarding how well a data set forms a trend. |
Nominated Adviser Statement
Beaumont Cornish Limited ("Beaumont Cornish"), is the Company's Nominated Adviser and is authorised and regulated in the
RNS may use your IP address to confirm compliance with the terms and conditions, to analyse how you engage with the information contained in this communication, and to share such analysis on an anonymised basis with others as part of our commercial services. For further information about how RNS and the London Stock Exchange use the personal data you provide us, please see our Privacy Policy.
Proactive Investors Australia Pty Ltd ACN 132 787 654 (the Company, we or us) provides you with access to the content set out above, including any news, quotes, information, data, text, reports, ratings, opinions, images, photos, graphics, graphs, charts, animations and video (Content) and this website (the Site) on the terms set out in this disclaimer, together with all other terms and conditions, disclaimers and other notices displayed elsewhere on this Site.
It is important for you to know that:
(a) none of the Content is, or is intended to be, general or personal advice
(b) the principal purpose of the Content is to provide factual information only and to comment on news;
(c) the Content does not contain or imply any recommendation or opinion intended to influence your financial decisions, including in respect of any particular security, portfolio of securities, transaction or investment strategy, and must not be relied upon by you as such;
(d) in providing you with the Content, we have not considered your objectives, financial situation or needs; and
(e) you should make your own enquiries and obtain your own independent advice prior to making any financial decisions.
The Content contains data (including but not limited to prices, statistics and calculated information) obtained from a variety of third party sources (Third Party Data). The Company does not make any representation or warranty that any of the Content, including the Third Party Data, will be reliable, accurate or complete. The Company disclaims all responsibility and liability arising in any way from any errors or omissions in the Content, including the Third Party Data, including any loss you may incur in connection with any action or decision made by you in reliance upon the Content or Third Party Data.
In certain circumstances the Company, its related bodies corporate, or their affiliates, may have received, or be entitled to receive, financial or other consideration in connection with providing information about certain entities on the Site, which may include the above Content.
FOR OUR FULL DISCLAIMER CLICK HERE